Hotfix release available: 2024-02-06a "Kaos".
upgrade now! [55.1] (what's this?)
New release available: 2024-02-06 "Kaos".
upgrade now! [55] (what's this?)
gravograph
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| gravograph [2018/04/30 21:10] – 5.56.201.162 | gravograph [2021/10/31 10:42] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== GravoGraph ====== | ||
| + | 3axis CNC Milling Engraving Mashine | ||
| + | X:230mm Y:84mm Z:15mm | ||
| + | XY: 1500mm/min | ||
| + | Z:300mm/min | ||
| + | VacuumTable 120mmx200mm | ||
| + | VacuumCompressor: | ||
| + | |||
| + | Firmware: | ||
| + | Chip: m328p | ||
| + | Driver: PololuLolo$random | ||
| + | Interface: RaspBerryPi3B running CNCjs | ||
| + | |||
| + | > GRBL 1.1 config: | ||
| + | $$ | ||
| + | $0=10 (Step pulse time, microseconds) | ||
| + | $1=25 (Step idle delay, milliseconds) | ||
| + | $2=0 (Step pulse invert, mask) | ||
| + | $3=4 (Step direction invert, mask) | ||
| + | $4=0 (Invert step enable pin, boolean) | ||
| + | $5=0 (Invert limit pins, boolean) | ||
| + | $6=0 (Invert probe pin, boolean) | ||
| + | $10=1 (Status report options, mask) | ||
| + | $11=0.010 (Junction deviation, millimeters) | ||
| + | $12=0.002 (Arc tolerance, millimeters) | ||
| + | $13=0 (Report in inches, boolean) | ||
| + | $20=1 (Soft limits enable, boolean) | ||
| + | $21=1 (Hard limits enable, boolean) | ||
| + | $22=1 (Homing cycle enable, boolean) | ||
| + | $23=1 (Homing direction invert, mask) | ||
| + | $24=500.000 (Homing locate feed rate, mm/min) | ||
| + | $25=1500.000 (Homing search seek rate, mm/min) | ||
| + | $26=250 (Homing switch debounce delay, milliseconds) | ||
| + | $27=0.800 (Homing switch pull-off distance, millimeters) | ||
| + | $30=1000 (Maximum spindle speed, RPM) | ||
| + | $31=0 (Minimum spindle speed, RPM) | ||
| + | $32=0 (Laser-mode enable, boolean) | ||
| + | $100=629.851 (X-axis travel resolution, step/mm) | ||
| + | $101=633.000 (Y-axis travel resolution, step/mm) | ||
| + | $102=633.000 (Z-axis travel resolution, step/mm) | ||
| + | $110=1500.000 (X-axis maximum rate, mm/min) | ||
| + | $111=1500.000 (Y-axis maximum rate, mm/min) | ||
| + | $112=1500.000 (Z-axis maximum rate, mm/min) | ||
| + | $120=40.000 (X-axis acceleration, | ||
| + | $121=40.000 (Y-axis acceleration, | ||
| + | $122=40.000 (Z-axis acceleration, | ||
| + | $130=231.000 (X-axis maximum travel, millimeters) | ||
| + | $131=85.000 (Y-axis maximum travel, millimeters) | ||
| + | $132=16.000 (Z-axis maximum travel, millimeters) | ||
| + | ok | ||
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
